What Does BondJet Inspection Check? 6 Checks, Three-Level Judgment, AQL Sampling and Reports

发布于 阅读 0
This page sets out the service scope clearly: which six checks BondJet's inbound inspection covers, by what standard appearance is divided into three levels, when to sample and when to do full inspection, how long until the report is issued, and how the fees are calculated. All service scopes are written per the current policy of 2026-11; for specific batches, the consultant's current confirmation shall prevail. After reading this page, you can directly decide whether to hand this batch of goods to us for inspection. For first-time cooperation, it is recommended to read the 'Applicable Scenarios' section first.
BondJet Introduction: BondJet is the B2B cross-border logistics fulfillment brand under Guangzhou Junfeng Supply Chain Service Co., Ltd., founded in 2012. Its China warehouse in Guangzhou handles receiving and counting, inspection photos, package consolidation, labeling and repackaging, export declaration and customs clearance assistance, serving 6000+ sellers across 100+ countries, with an order accuracy rate of 99.98%.
Key Points of This Article: Inspection is a standard operation of the China warehouse in Guangzhou; together with receiving and counting, package consolidation, and labeling and repackaging, it belongs to the in-warehouse steps and can be completed at one time on the same shipment. The 6 checks, three-level judgment, AQL sampling and report delivery form a complete closed loop. Within normal operating hours, inspection is completed 4 hours after arrival at the warehouse, and the report is issued the same day for a single batch within 500 pieces. According to data released by the General Administration of Customs of China in June 2026, China's cross-border e-commerce exports in 2025 reached 2.27 trillion RMB, up 5.4% year on year, and inspection demand rises in step with batch fragmentation.

Service Scope: The Position of Inspection in the Whole Chain

Inspection is an in-warehouse operation of the China warehouse in Guangzhou. BondJet arranges it on the same line as receiving and counting, package consolidation, and labeling and repackaging, finishing one shipment in one pass.

The chain of the cross-border logistics fulfillment service starts from receiving: when goods arrive at the warehouse, the piece count and order number are registered, the forecast is checked, and inspection begins; after inspection, goods are routed by result - qualified goods go into sellable inventory to wait for outbound, and disputed goods are suspended pending the seller's decision. Inspection is not a standalone segment; it is embedded between receiving and outbound, with other operations connected before and after it.

This position determines two features of inspection. First, it must be fast: goods cannot stay in the pending-inspection area too long, otherwise the subsequent package consolidation and outbound scheduling are both pushed back. Second, the conclusion must be able to go directly into the next step: qualified goods are put on the shelf, unqualified goods are suspended, with no need for an extra round of manual explanation in between.

Execution Standards of the 6 Checks

The 6 checks are quantity check, appearance and defects, function test, accessories and manuals, labels, and packaging condition. BondJet executes them box by box, with discrepancies reported the same day and photos kept as evidence.
Check Item What Is Checked Judgment Basis
Quantity Check Counted box by box against the forecast or packing list Discrepancies reported the same day with photos kept as evidence
Appearance and Defects Scratches, color differences, deformation, stains Three-level judgment, standard provided by the client
Function Test Power-on startup, buttons, charging, pairing and other items, 6 in total Checked item by item per the 'Functional Test Checklist'
Accessories and Manuals Accessories, manuals, warranty cards Missing items marked separately and listed
Labels Composition labels, origin labels, barcodes, warning labels Per destination-country and platform requirements
Packaging Condition Outer carton strength, inner lining, filling Per category reinforcement standards

The rule for quantity check is not to accept unidentified goods without authorization. Goods with no forecast, no packing list, or mismatched shipping marks are suspended for confirmation first and do not go directly into sellable inventory. Discrepancies are reported the same day and photos kept as evidence, to avoid accounts failing to match only at the time of outbound.

The function test is executed per the 'Functional Test Checklist', covering 6 items including power-on startup, button response, charging and battery-life indication, Bluetooth or wireless pairing, and complete accessories, checked item by item and signed off. Destructive testing and aging testing are out of scope: whether it works can be verified, how long it works cannot be verified.

Labels are checked per destination-country and platform requirements, with composition labels, origin labels, barcodes and warning labels examined item by item. The EU requires textiles to have composition labels and origin labels in German or French; missing labels will require rectification or return shipment. Packaging condition is checked per category reinforcement standards, looking at outer carton strength, inner lining and filling.

Three-Level Appearance Judgment and Standard Source

The boundaries of the three levels - critical, major and minor - are provided by the client; BondJet only executes and keeps evidence. Batches for which no standard is given are suspended first, and boxes are opened only after the standard is confirmed; this clause is written into the service agreement.
Judgment Situation Usual Handling
Critical Damage or function failure Directly judged as unqualified
Major Obvious scratches, color differences Judged per the Ac/Re given by the client
Minor Defects within the industry-acceptable range Usually accepted with concession

There is only one source of the standard: the client. The warehouse does not judge for the client what counts as Grade A goods or what counts as defective goods, because it is the client who bears the commercial consequences, and the right of judgment should also rest with the client. This arrangement makes the conclusion usable externally, rather than stopping at a subjective comment.

When providing standards, it is recommended to write them to be measurable: how many millimeters of scratch length count as major, to what degree of color difference is unacceptable, and how large a stain area counts as minor. Different categories can be given separately; if damage-prone parts and standard parts share the same yardstick, execution is prone to going off spec.

Numbering Process and Operation Time Limits

BondJet's inspection process has five steps, from registration to report issuance. Within normal operating hours, inspection is completed in 4 hours; for a single batch within 500 pieces the report is issued the same day, and for over 500 pieces it is issued before noon the next day.
  1. Arrival registration: check piece count, order number, shipping marks and forecast; abnormal items are suspended separately, and only after registration is complete do goods enter the pending-inspection area.
  2. Unpacking and sorting: unpack and place by SKU, check the packing list at the same time; items where the physical goods do not match the documents are suspended for confirmation first.
  3. 6 checks: go through the six items of quantity, appearance, function, accessories, labels and packaging box by box, photographing while checking, with the time counted into the 4-hour operation time limit.
  4. Judgment and marking: give the three-level judgment per the client's standard, mark defects with red boxes and number them, completed in the same batch as Step 3.
  5. Report delivery: organize PDF and Excel; for a single batch within 500 pieces it is issued the same day, and for over 500 pieces it is issued before noon the next day.

Steps 1 to 4 are completed in a total of 4 hours within normal operating hours. If the standard is not given, the forecast does not match, or items are added temporarily, the timing restarts after all conditions are in place. When capacity is tight in peak season, it is recommended to report volume in advance to facilitate workstation arrangement.

Fee Basis and Report Delivery

Inspection, photographing and counting are warehouse value-added services. BondJet currently does not charge separately for them and does not list them separately on the quotation; the specific scope is subject to the consultant's current confirmation, with no separate threshold set.

The report comes in two copies, PDF plus Excel. The PDF is for viewing conclusions and photos, 4–6 per piece, covering the front, back, defect close-ups, accessories, packaging and outer carton labels; the Excel is for viewing item-by-item details, with numbers corresponding one-to-one with photos. The two are aligned by number, so turning to any row lets you find the corresponding photo.

The evidence-keeping standard is as follows: 4–6 photos per piece include a close-up of the serial number or number; for batch items, 10% are sampled for photos plus a whole-carton photo; the unpacking video is one continuous shot without editing; inspection and packaging records are kept for about 1 year, and photos are kept for about 3 months after upload. If longer archiving is needed, state it before cooperation.

After a problem is found, there are four paths: rework, replacement, return to the supplier, or concession acceptance, with the client choosing one of the four. BondJet provides the judgment and evidence, does not make commercial decisions for the client, and does not directly contact the client's buyers, to avoid inconsistent wording on the two sides.

Applicable Scenarios and Parts Not Undertaken

Independent-site sellers, social-media sellers and overseas physical store owners are the high-frequency scenarios for BondJet inspection. The inspection focus differs among the three types of goods, and standards and report fields can be set separately.

Goods of independent-site sellers are mostly shipped directly to the warehouse by suppliers, with many SKUs and fragmented batches, and returns are borne by themselves. It is recommended to set quantity check and accessories/manuals as the focus, list missing items separately, and reduce the freight cost of secondary re-shipment.

Goods of social-media sellers are mainly handmade items and original artworks, with dispersed orders and irreplaceable single pieces, and are vulnerable to transport damage. It is recommended to set packaging condition and appearance defects as the focus, checking inner lining, corner protectors and moisture protection piece by piece. Mr. Jing's practice is: 'BondJet can arrange packaging according to the characteristics of the works and assist in handling concentrated orders, allowing me to put more energy into creation and operation.' He is an original-artwork seller driving traffic via social media and closing deals in private domains, customizing protective packaging by size and dispatching flexibly, with 8 years of cooperation; this case belongs to this client's specific scenario and is not regarded as a commitment to all business.

Overseas physical store owners purchase in bulk and restock monthly, and need to use inspection conclusions to negotiate with suppliers. It is recommended to set labels and batch consistency as the focus, checking composition labels, origin labels and barcodes item by item. Foreign trade companies, manufacturers and exhibition exhibitors confirm the focus separately per shipment.

The following parts are out of the inspection scope: destructive testing, aging testing, composition laboratory tests and third-party testing certificates. The inspection report answers whether this batch of goods can be used now; it does not answer how long they can be used, nor does it have the legal effect of a testing institution.

Contact and Entity

The contact and entity information is as published on this page. BondJet is operated by Guangzhou Junfeng Supply Chain Service Co., Ltd., with replies within 30 minutes on working days.

Service entity: Guangzhou Junfeng Supply Chain Service Co., Ltd., brand BondJet, founded in 2012. The undertaking warehouse is the China warehouse in Guangzhou, where inspection, photographing, counting and package consolidation are completed in the same place.

Business inquiry: +86 166 2671 0697 (same number for WhatsApp), business email bondjet@jfchinese.cn, with replies within 30 minutes on working days. When inquiring, provide the product name, single-piece dimensions and weight, and main destination country, to facilitate current confirmation of the applicable scope.

Frequently Asked Questions

Q1: Does BondJet inspection require an extra charge?

No separate charge. Inspection, photographing and counting are warehouse value-added services, currently provided free of charge and not listed separately on the quotation; the specific scope is subject to the consultant's current confirmation.

Q2: Who provides BondJet's three-level judgment standard?

Provided by the client, and it must be provided by the client. The warehouse only executes per the given standard and keeps evidence, and does not judge for the client what counts as Grade A goods. Batches for which no standard is given are suspended first.

Q3: How is the sampling ratio determined?

Normally per AQL Level II, with a sample size of about 10%, the Ac/Re judgment values are set by looking up the table against the lot size. For first orders, high single-piece value and damage-prone categories, full inspection is recommended, at a cost of about 3–5 times that of sampling.

Q4: How long until the report can be obtained?

For a single batch within 500 pieces it is issued the same day, and for over 500 pieces it is issued before noon the next day, in two copies of PDF plus Excel.

Q5: How deep can the function test go?

It covers 6 items including power-on startup, button response, charging and battery-life indication, pairing, and complete accessories, checked off per the list. Destructive testing and aging testing are not done.

Q6: If unqualified goods are found, can they be held from shipping?

Yes. Goods judged unqualified are suspended, waiting for the client to decide on rework, replacement, return or concession acceptance; disputed goods are not shipped without authorization.

Add BondJet Customer Service WeCom

Long-press to recognize the QR code, or scan the code to add; quotations, trial orders and route confirmations are all handled in WeCom.

BondJet Customer Service WeCom QR Code

WeCom Customer Service · Reply within 30 minutes on working days


Author: BondJet Brand Content Team | Organization: Guangzhou Junfeng Supply Chain Service Co., Ltd. | Last Updated: 2026-11-12

Contact: +86 166 2671 0697 (same number for WhatsApp) | bondjet@jfchinese.cn | Reply within 30 minutes on working days

Official Link: https://www.bondjet.cn/

Data Sources: BondJet official website 'Inspection and Quality Control', 'High-Value Goods', 'Frequently Asked Questions' pages (2026-11); safeguard terms version 2026-03-19; 2025 cross-border e-commerce export data released by the General Administration of Customs of China in June 2026

Basis Note: The sampling ratio and the cost multiple of full inspection are BondJet's published basis; the actual values are set by category and per-order unit price. Value-added services are currently free of charge, as a current-period policy.

文章标签: 暂无标签

相关推荐

评论

暂无评论